Poker Chip Blog

An informative and hopefully enlightening blog discussing Poker News, Poker Supplies and mostly Poker Chip Design.



Huge "Dealer Button Bazaar" Group Buy!

SALVATORE APODACA - Tuesday, May 02, 2017

Huge "Dealer Button Bazaar" Group Buy! We're taking order now until May 17th. Order here.

Chocked full of old buttons that are out of print or have never been printed before, new buttons and buttons we've only offered on a limited basis.

Just so you understand that there is a community of people who have an obsession with poker chips. It's about the art and construction as much as it is about the game. Folks spend thousands of dollars on different sets of new and used poker chips from manufacturers as well as from real casinos that change their styles of poker chips often or close and auction them off.

Seriously, check out these button designs and you'll see an array of different designs for dealer buttons that are related to all kinds of real and fictional casinos as well as designs that were popular amongst those in the poker chip community - call them aficionados if you must. 

(From left to right, top to bottom) Casablanca Casino, Casino Aztar, Even Stevens, Garden City, Oak Tree, Par-A-Dice Riverboat Casino, Casino Pointe After, Rounders, Terrible's, Casino de Isthmus and President Casino on the Admiral.

Dealer buttons are obviously a collector's passion in some circles. We like to match them to sets that people purchase over the years from actual casinos or group buys for chips that have formed over the years on poker chip forums including Chiptalk, Poker Chip Forum and Home Poker Tourney.

Below are a few more designs we also contributed to the group buy.

Of course the Top Hat & Cane buttons are for the many folks lucky enough to have the World TH&C poker chips that are no longer in print but were very popular for many years.

There have been no group buys for Stardust chips but we plan on releasing some replica chips in the near future for that iconic now closed casino.

There also a few more designs not shown here but below are the Atlantic Club buttons. And the interesting Iron Bank dealer buttons in homage to that great show on television I probably don't have to mention.

This group buy as mentioned above was started on Poker Chip Forum. You can follow the link. Or you can just purchase some of the buttons from our store for a limited time. The link to our Group Buy catalog is right here.

These are just some of the fun things us poker chip enthusiasts do to pass the time. Well, it's my job but you get the idea. It's a passion. 

Enjoy!
Salvatore


Price Increase on Custom/Stock Ceramic Chips

SALVATORE APODACA - Tuesday, August 09, 2016

UPDATE: Some changes were made to this document on August 12th.

It's unfortunate but change is inevitable. We were forced recently by the market to raise our prices and minimums on our custom and stock ceramic poker chips.

Hopefully the slightly higher prices won't scare you away.

Here are the new minimums for the different sized chips, plaques and buttons:

Ceramic Poker Chips – Minimums are 50 for each design or denomination
39 mm Custom Ceramic Poker Chips - 10 grams
43 mm Custom Ceramic Poker Chips - 12 grams
47 mm Custom Ceramic Poker Chips - 14 grams
Octagon 43.5 mm Custom Ceramic Poker Chips - 14 grams

Ceramic Dealer Buttons – Minimums are 5 for each design
2 Inch Custom Ceramic Dealer Buttons - 25 grams
60 mm Custom Ceramic Poker Buttons - 40 grams

Ceramic Plaques - Minimums are 10 for each design or denomination
68 mm Custom Ceramic Poker Plaque - 40 grams
82 mm Custom Ceramic Poker Plaque - 60 grams
85 mm Custom Ceramic Poker Plaque - 40 grams
94 mm Custom Ceramic Poker Plaque - 80 grams
107 mm Custom King Size Ceramic Poker Plaque - 100 grams

Oval Ceramic Plaques - Minimums are 10 for each design or denomination
Oval 68 mm Custom Ceramic Poker Plaque - 40 grams
Oval 82 mm Custom Ceramic Poker Plaque - 60 grams
Oval 94 mm Custom Ceramic Poker Plaque - 80 grams
Oval 107 mm Custom King Size Ceramic Poker Plaque - 100 grams

If you have more questions let us know by sending us an email to oldwestps@gmail.com.

Thanks for your patronage.
Salvatore



Aligning Edge Spots in Your Poker Chip Design

SALVATORE APODACA - Thursday, June 02, 2016

One of the most common elements in poker chip design is the aligned edge spot.

This of course is a carryover from clay poker chips that are made using strips of clay resin during the molding process. This isn't something a ceramic poker chip designer or printer has the luxury of doing but they can easily simulate it. Graphic designers often use math or software scripts to match the elements of the face of a cylinder to the circumference's matching design. This can work well but how does someone achieve a match without the use of math skills that not every designer is skilled at or wishes to employ?

Well, it's simply done with the use of grids or graphs. Adobe Illustrator is an excellent vector design program that every designer should learn to work with. It has two tools that work extremely well together for a poker chip designer. The Polar Grid Tool and the Rectangular Grid Tool can both be found under the Line Tool by simply clicking and holding. 

First you'll have to decide on how many edge spots you might want, how they'll look on the face and the circumference, what color you plan for them to be, etc. For now let's concern ourselves merely with learning how to use both these tools to get the desired result of matching meeting points between the face and the rolling edge of the chip.

Choosing the Polar Grid Tool in your document. You can actually download Illustrator vector templates for our poker chips here under our Design Guide. You'll want to click in the upper left corner of your artboard like below. You'll be confronted with a dialog. You'll want to make it the size of your poker chip. In this example I am using a 39 millimeter template. So fill it in with 39 mm for both the top measurements. Leave the Concentric Dividers option at zero. Then depending on how you plan to set up your edge spots you'll want to fill in the appropriate number of Radial Dividers. This is the most important number and you'll want to remember that number.


I'll use 48 here because it will work well for the example. When click "OK" you'll probably end up with highlighted transparent guides. I always give those guides a stroke weight of about .25 pt. You can actually make this a lower number if you prefer but it's important to give it a color that you'll be able to tell apart from your design palette much like the standard guides in Illustrator. Also make sure the Polar Grid is centered perfectly on your artboard and in a top layer on its own. Then you'll want to lock it down so it doesn't move.

This is your guide for your edge spots on the face of the chip. You can place them however you please but usually you'll want to keep to a specific pattern so that the printers can easily align this to your rolling edge artwork. The typical edge spots will be placed at specific points on say a clock. I used 48 for this reason. It's divisible by 12. So at 12 o'clock on the design you can place two edge spots next to each other. They can take up two grid segments each. I usually use one of the rectangle tools. For a 48 segment grid this would usually be a 5 mm square placed along the top at 17 mm on the x axis and another one placed at 22 mm on the x axis (both positioned at 2.5 mm on the y axis). Remembering this can make it easy in future designs but sometimes our customers or designers will have or want some oddly shaped edge spots. In that case you just have to use the grid for the appropriate alignment.

You can also use the pen tool to build your edge spots. The basic idea is to make sure they line up with your grid segments as shown above. You can copy these to the six o'clock position on your design by rotating and copying them then moving them to the 36.5 mm position on the y axis. Then if you select all four edge spots you can simply rotate 90 degrees and copy for the remaining edge spots.

Once you've got these lined up you can go ahead mess with their shape however you like by using the pen tool or pathfinder tricks to make them look more authentic or original. It's really up to you. And it's not really that necessary at this point to do the trimming of the squares to fit the circular design of the chip. We can always do that trimming for you or it can be done using a layer mask. It's not that important. What's really important is to make sure the edge spots align with your grid segments.

The next part is where this will all fall into place. You can open the Illustrator template for the 39 mm edge on our Design Guide page or you can create a document that is 125.5 mm high by 3.3 mm wide in Illustrator and fill it with a base rectangle of the same size. This is the rolling edge of the poker chip. Now instead of using the Polar Grid you'll want to use the Rectangular Grid. Keep in mind that you'll want to match the number of segments that were created in the previous example. We have 48 grid segments for the face of the chip. The Rectangular Grid is a little trickier. You can use the outer rectangle as a frame or not - it's your choice. I usually check it. But you always want the number for vertical dividers to be one less than the Polar Grid radial dividers. That's because that outer rectangle is counted as one vertical divider. So you will always have to use one less vertical divider. In this case we use 47 in order to get 48 rectangular grid segments.

Make sure it's centered on the artboard, there is a stroke weight for the guide lines and it's in the top layer but don't lock it down just like you did with the Polar Grid. Now you can use those grid segments to set up the aligning edge spots. It's very simple from that point on. 

There are all kinds of cool tricks you can use this for in your designs. For instance, if you wanted to wrap a snake around your poker chip you could use this to achieve that quite easily. In this case it's a simple 8 spot alignment. Do remember though that if you want these alternating edge spots to align to the second face of the chip you'll need to make a second chip face and do a vertical reflection of those original edge spots. That's the trick of alternating edge spots. 

And even more important you can always ask us to do your artwork for free when you place an order with us. Also if you have questions regarding this or any other poker chip design dilemmas please feel free to send me an email to oldwestps@gmail.com

Salvatore Apodaca
Designer
Old West Poker Supplies LLC
oldwestpokersupplies.com


Using our CMYK Color Chips Correctly

SALVATORE APODACA - Thursday, June 02, 2016

Our CMYK Color Wheel Chips which can be found here for purchase are excellent for choosing chip colors when you decide to customize your ceramic poker chips, buttons or plaques. However, always remember that choosing colors based on what you see will only work if you can actually "see" them. That means that we are often making color decisions in really poor light. Often we assume the lights in our rooms or environments are lit well enough for us to make important color decisions. We get dressed in half lit rooms. We read under really dim lamps.

When choosing your chip colors you should be viewing the CMYK Color Chips in direct rather bright light. It's a good idea to turn on a bright desk lamp and get plenty of light when looking at these Color Wheel Chips. You want to have the best available light when making color choices.

Color professionals (yes, there are color pros) often use big overhead lamps or even huge desktop size booths with daylight rated lamps in them so that they can fully experience the colors they have to choose or create. You should try your best to get some good light.

I use an extra desk lamp that is portable so I can fold it away when I'm not using it. It has three dimmer levels, runs on lithium battery power and is rechargeable. 

Here's a link to the lamp I use.
http://www.amazon.com/Modern-Student-Office-Bedroom-Outdoor/dp/B013QRJF5Y



New CMYK Color Wheels! IMPROVED & EXPANDED!

SALVATORE APODACA - Friday, February 19, 2016

We are currently working on an expanded color wheel set. We will double the available colors that you can use in your designs. So that's 300 or more colors to choose from! More violets, more browns, more oranges - just more! The sets should be available around the second week in March. We currently only have a couple of the old sets left so you may want to wait and get this new expanded set. I'll have more information soon. Happy designing.
- Salvatore


Rounders Replica Ceramic Chips Pre-Order NOW!

SALVATORE APODACA - Sunday, August 02, 2015

"Rounders" is a classic of poker cinema in which the character "Teddy KGB" is a Russian gangster who runs an underground poker club. His house chips are branded with a bear in keeping with the Russian theme. The chips made for the film were originally a clay chip and have been replicated many times since the release of the film. We have finally decided to fashion our own version of the design except we went a step further and added high denomination plaques, a bounty button and a dealer button which I'm quite sure have never been offered before.

You can check them all out and pre-order them right here:

http://www.oldwestpokersupplies.com/shop/stock-ceramic-poker-chips/rounders-replicas

As stated in our previous announcement these chips are in the prototype stage which means the design may be tweaked very slightly but if you like the current design and are quite prepared to move forward we can customize a set for you right now. Just send us an email.

Here are the new additions to the set.

A couple of high denomination plaques for the big kids table...


And check out the new bounty and dealer buttons! I love these designs. They scream "red scare". lol.




Poker Chip Blog

Recent Posts



Archive


Tags